The writer is making several great points on How to Install a Bathtub Yourself in general in this post below.
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a new one is also a moderately tough task. If the old tub is readily easily accessible, the task can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub as well as embeded in the brand-new one. Make certain you have actually qualified on your own for the task and also are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to think about using one prior to you begin. Chances are you may need a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your bathroom if you have actually currently acquired a new tub as well as don't need to change the setup of your previous water pipelines.
Your devices as well as product checklist ought to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Protect the faucet in place with the producer given backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub up until the level reviews level.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water system as well as check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used a minimum of once as this will resolve it right into its final position.
Preparing for the Installation
To start with, the supporting frame provided with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with wetness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that report about Installing A Bathtub through an acquaintance on our other domain. Sharing is caring. Helping people is fun. Bless you for your time. Visit us again soon.
Click On This Link